Product Information Sheet - 10-5036VB-2-.093X36-SF2 ARLON ThermaVac® Vacuum Bag Membranes ARLON ThermaVac® vacuum bag membranes are manufactured for high strength, high tear, silicone rubber with a micro-surface texture to reduce tackiness without the use of talc. Silicone rubber vacuum bag membranes are a reusable option that can replace disposable films, the labor cost required to prepare the film for each run, and resulting waste stream of single use.

(800) 935-2940 solutions@rogerscorp.com

Product Design and Construction
Side 1: 2.36 mm Cured Overall Product Thickness: 2.36 mm Color: Red	Side 1

Basic Physical Properties	Value	Units	Test Method
Durometer	51	Shore A Points	ASTM D2240
Tensile Strength	8828	kPa	ASTM D412
Elongation	794	%	ASTM D412
Tear Strength	43.8	N/mm	N/A
Specific Gravity	1.13	N/A	Arlon SQA-TMS-024
Width	914	mm	Arlon SQA-TMS-012

Construction	Value	Units	Test Method
Construction Designation	Construction 2	N/A	Code Definitions
Color	Red	N/A	N/A

Extended Physical Properties	Value	Units	Test Method
Total Product Weight	0.92	kg/m2	N/A
Compression Set	9.9	%	N/A
Elastic Modulus @ 25%	768	kPa	ASTM D412
Elastic Modulus @ 50%	1,071	kPa	ASTM D412
Elastic Modulus @ 100%	1,492	kPa	ASTM D412
Elastic Modulus @ 300%	3,099	kPa	ASTM D412

Heat and Flame	Value	Units	Test Method
Min. Operating Temp.	-57°	°C	N/A
Max. Operating Temp.	232°	°C	N/A
Glass Transition Temp (Tc)	-126°	°C	ASTM 3418

Processing and Packaging	Value	Units	Test Method
Shelf Life	60	Months	N/A
Shelf Life Storage Temp	21°	C	N/A

Standard color is red or grey. Available in custom colors.
Standard surface finish is super fine fabric. Other surface finishes available.

Solid Silicone Sheet Thickness Tolerances

Includes cured and uncured solid silicone sheeting with and without reinforcement produced by calendaring. Does not include uncured, unsupported, solid silicone compound pre-formed into sheets by milling.

[1] In the case of laminated products these tolerances apply only to the individual layers and not the overall thickness of the laminate. Laminate thicknesses are nominal.

[2] Imperial or metric tolerance govern based on the measurement system of the part description.

Note: Shelf life is defined as the duration of time for which the product will meet the physical characteristics outlined on this page. It does not guarantee the product's usefulness in all applications.

Note: Bond Strength ASTM XXXX test methods:

• For Constructions 0-9, any reported bond strength is "Ply Adhesion"
• For Supported Tapes, reported bond strength is from internal method where tape is hung up, stretched, and rolled up -- the strength required to unroll is reported : ASTM D2148
• For unsupported tape, the reported value is a Government Bond where 2 pieces are bonded together and plied apart: MIL-I-46852C

The data presented in this document represents typical values for the production material. Typical values should not be used for specification limits. Material colors displayed are representations only, actual colors will vary. The information contained in this Data Sheet is intended to assist you in designing with Rogers’ Elastomeric Material Solutions. It is not intended to and does not create any warranties, express or implied, including any warranty of merchantability or fitness for a particular purpose or that the results shown in this Data Sheet will be achieved by a user for a particular purpose. The user should determine the suitability of Rogers’ ARLON products for each application. The Rogers logo, ARLON, and the ARLON logo are trademarks of Rogers Corporation or one of its subsidiaries. © 2020 Rogers Corporation. All rights reserved. www.rogerscorp.com. Modified: 04/28/2026